Waterborne epoxy primer additives should support the substrate interface and corrosion-control design, not conceal poor preparation or incomplete cure. Identify the defect before dosing: surface retraction may justify a wetting trial, persistent microfoam may justify a defoamer trial, while early rust, weak adhesion or soft film requires a substrate, formulation or cure investigation.
Screen D547 wetting.
Screen D9904BR.
Fix preparation and epoxy–amine chemistry.
Start with the substrate specification
State whether the primer will coat carbon steel, galvanized steel, aluminum, concrete or another substrate. Define cleaning, abrasive profile, soluble-salt limit, dust removal and maximum time before coating. For concrete, record moisture and surface condition. Silicone, oil, release agent, flash rust or salt contamination can defeat adhesion regardless of additive choice.
Protect epoxy–amine cure chemistry
Calculate component ratio from current epoxy equivalent weight and amine hydrogen equivalent weight on a consistent solids basis. Fix induction time, dilution sequence, pot life, wet film build, temperature, humidity and airflow. Water evaporation and chemical cure must both progress. Wrong stoichiometry, amine blush or premature water exposure is not a wetting-agent problem.
Compare the supported routes
Use CHLUMICRYL® WD-D547 for waterborne primer wetting only for an interface problem, CHLUMICRYL® DF-D9904BR for process air for documented grind-stage foam, and CHLUMIAG® 3467 only after its reactive chemistry is shown to fit the binder and cure design.
| Route | Published evidence | First use | Boundary |
|---|---|---|---|
| AGESIN® WD-D547 | 100% active; 0.1–0.5% total; waterborne, solvent, solvent-free and UV systems | Retraction, localized craters or incomplete substrate entry | Does not supply surface preparation, cure or corrosion protection |
| AGESIN® WE-D9904BR | 30% active in DPM; water-based systems; 0.1–1.0% total | Air generated in pigment grind or high-shear processing | Co-solvent premix and high-shear grind addition required; post-addition not recommended |
| CHLUMIAG® 3467 | Reactive OH route for polyurethane; public OH value only ≤85 mg KOH/g | Only a documented PU or hybrid reaction design | Ordinary epoxy/amine curing does not use the stated OH/isocyanate mechanism |
Use D547 for an interface-wetting question
Screen low, middle and high levels within 0.1–0.5% while holding substrate preparation, viscosity, application and film build constant. Record retraction, pinholes, edge coverage and crater count. The product page also describes qualitative leveling, recoat and defoaming effects, but those observations do not prove corrosion performance or establish an optimum dose in a filled epoxy primer.
Use D9904BR for documented process air
D9904BR contains 30% active material in DPM. Premix it with co-solvent and add it under high shear during grinding as the page directs; post-addition is not recommended. Measure grind and letdown density, foam decay, entrained microbubbles and cured-film pinholes. Reject doses that create craters, pigment separation, gloss changes or storage instability.
Keep 3467 outside the generic shortlist
The 3467 page describes a reactive hydroxyl route for polyurethane and provides only an upper-limit OH value, not the exact hydroxyl number needed for stoichiometry. That chemistry is unrelated to a normal epoxy/amine primer unless a documented hybrid system deliberately includes an isocyanate reaction. Require exact OH, NCO equivalent, solids and NCO/OH calculation before any such experiment.
Prepare controlled primer panels
ASTM D823 describes practices for applying uniform coating films to test panels. Record applicator or spray settings and both wet and dry film thickness. Include prepared and intentionally challenged substrate panels only when the protocol defines the challenge; uncontrolled contamination produces anecdotes rather than comparative evidence.
Run a single-variable matrix
| Panel set | Change | Primary measure | Release gate |
|---|---|---|---|
| A | Current control | Wetting, density, cure and adhesion baseline | Corrosion and recoat |
| B–D | D547 low/mid/high | Retraction, craters and edge coverage | Adhesion, water resistance and topcoat |
| E–G | D9904BR low/mid/high | Wet density, foam and pinholes | Crater, storage, adhesion and corrosion |
| H | Preparation or cure correction | Contamination, stoichiometry or water release | Repeat full control |
Locate adhesion failure
ASTM D3359 provides tape methods for coating adhesion. Use a consistent film thickness and cure age, document the substrate and note whether failure is adhesive, cohesive or intercoat. The test is comparative and its precision varies by substrate and coating; follow the project specification when quantitative pull-off testing is required.
Use corrosion exposure as a system test
ASTM B117 provides the apparatus and operating practice for salt-spray exposure, but it does not prescribe a universal exposure period or predict service life by itself. Define scribe preparation, duration, evaluation intervals and acceptance limits. Compare blistering, rusting, undercutting and adhesion retention after recovery.
Approve recoat and service performance
Apply the intended intermediate or topcoat at minimum, target and extended recoat windows. Check intercoat adhesion, lifting, wrinkling and cure. Then test water, chemical, impact or abrasion resistance required by the service environment. A primer can look defect-free yet lose adhesion after immersion or allow corrosion at holidays and edges.
Decision rules
- Correct preparation, contamination and epoxy–amine cure before screening additives.
- Use D547 only for a reproduced interface-wetting defect.
- Use D9904BR only through its documented grind-stage process for measured air.
- Do not treat 3467 as a generic epoxy-primer additive without a documented PU hybrid reaction route.
Information to send with an inquiry
Provide substrate, preparation standard and profile, contamination checks, epoxy and hardener data, EEW/AHEW, solids, mix ratio, induction, pot life, pigment volume, pH, viscosity, film build, application, cure, recoat schedule, exposure requirement and defect photographs.
Ask Longchang for a controlled waterborne epoxy primer additive test plan.