{"id":10587,"date":"2026-07-12T00:00:41","date_gmt":"2026-07-12T00:00:41","guid":{"rendered":"https:\/\/longchangchemical.com\/?p=10587"},"modified":"2026-08-09T13:43:15","modified_gmt":"2026-08-09T13:43:15","slug":"waterborne-industrial-coating-additives","status":"publish","type":"post","link":"https:\/\/longchangchemical.com\/hu\/waterborne-industrial-coating-additives\/","title":{"rendered":"Waterborne Industrial Coating Additives: Wetting & Air"},"content":{"rendered":"

Waterborne industrial coating additives<\/strong> should solve a reproduced defect without weakening adhesion, corrosion resistance, impact or recoat. Separate substrate wetting, surface leveling and process air first. Then select one documented route and keep resin, pigment volume, pH, viscosity, film build and cure constant.<\/p>\n

\n
\n
Retraction or poor entry<\/strong>
Screen 3071 wetting with a foam gate.<\/div>\n
Flow or leveling defect<\/strong>
Screen 3345.<\/div>\n
Grinding, pumping or spray air<\/strong>
Screen 3062; keep 094 conditional.<\/div><\/div>
Original waterborne industrial coating map: separate interface wetting, exposed-film flow and process air.<\/figcaption><\/figure>\n

Define substrate and service before additives<\/h2>\n

Record metal, plastic, wood or mineral substrate; cleaning and profile; primer or direct-to-substrate design; exposure; and recoat schedule. Oil, salts, silicone contamination, weak pretreatment or flash rust can look like a wetting problem. An additive does not supply corrosion protection, moisture tolerance or chemical cure.<\/p>\n

Compare the current product evidence<\/h2>\n\n\n\n\n\n\n\n\n
\u00datvonal<\/th>\nK\u00f6zz\u00e9tett t\u00e9nyek<\/th>\nBest first use<\/th>\nBoundary<\/th>\n<\/tr>\n<\/thead>\n
CHLUMIWE\u00ae 3071<\/a><\/td>\n0.1\u20131.0% total; water\/solvent\/UV; wetting; no public active-content value<\/td>\nRetraction or poor substrate entry<\/td>\nPage warns of foam stabilization in waterborne systems<\/td>\n<\/tr>\n
CHLUMILE\u00ae 3345<\/a><\/td>\n100% active; 0.1\u20131.0% total; all three system types<\/td>\nWetting\/leveling and surface uniformity<\/td>\nMust preserve adhesion, recoat and crater resistance<\/td>\n<\/tr>\n
CHLUMIAF\u00ae 3062<\/a><\/td>\n100% active; industrial-coating dose 0.1\u20130.5%; water\/solvent\/UV<\/td>\nProcess foam and entrained microair<\/td>\nSolvent dilution needs stability and defoaming tests<\/td>\n<\/tr>\n
CHLUMIAF\u00ae 094<\/a><\/td>\n100% active paste; 50\u2013500 ppm; water-only; multi-step dilution and immediate-use working solution<\/td>\nOnly a supplier-confirmed specialized foam study<\/td>\nPublic applications emphasize extraction, fluids, fermentation, papermaking and wastewater rather than coatings<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Use 3071 for measured entry failure<\/h2>\n

Start low within 0.1\u20131.0% and keep application conditions fixed. Measure retraction, crater count, edge coverage and substrate wetting. Because the page warns that 3071 may stabilize foam in waterborne systems, also record wet density, foam decay and cured pinholes. Better spread is not proof of better adhesion.<\/p>\n

Use 3345 for controlled flow work<\/h2>\n

3345 has a documented 0.1\u20131.0% total range and 100% active content. Compare leveling, orange peel, gloss and sag at equal viscosity and film build. Reject a smoother panel if it increases craters, reduces intercoat adhesion or narrows the recoat window. Record any predilution and co-solvent because they are process variables.<\/p>\n

Use 3062 for industrial-coating foam<\/h2>\n

3062 provides a specific industrial-coating range of 0.1\u20130.5% total. Identify whether air enters during dispersion, letdown, pumping or spraying. Compare wet density, foam height and decay, microbubbles and cured pinholes. If solvent dilution is considered, the page requires stability and defoaming-performance checks first.<\/p>\n

Keep 094 conditional<\/h2>\n

094\u2019s page gives a low 50\u2013500 ppm range but also requires staged dilution: first below 60%, then 10\u201340 times with water, with the working solution prepared and used immediately. Its listed applications are not coating-specific. Do not treat it as an easy drop-in industrial-coating defoamer; require written supplier confirmation, an exact working-solution calculation and compatibility data.<\/p>\n

Run a single-variable matrix<\/h2>\n\n\n\n\n\n\n\n\n
Panel set<\/th>\nChange<\/th>\nPrimary measure<\/th>\nRelease gate<\/th>\n<\/tr>\n<\/thead>\n
A<\/td>\nUnchanged control<\/td>\nWetting, flow, air, cure and adhesion baseline<\/td>\nCorrosion, impact and recoat<\/td>\n<\/tr>\n
B\u2013D<\/td>\n3071 low\/mid\/high<\/td>\nRetraction and edge coverage<\/td>\nFoam, adhesion and topcoat<\/td>\n<\/tr>\n
E\u2013G<\/td>\n3345 low\/mid\/high<\/td>\nLeveling, gloss and sag<\/td>\nCrater, adhesion and recoat<\/td>\n<\/tr>\n
H\u2013J<\/td>\n3062 within 0.1\u20130.5%<\/td>\nDensity, foam and pinholes<\/td>\nGloss, storage and full-system durability<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Keep dose bases and interactions clear<\/h2>\n

3071 lacks a public active-content value, while 3345 and 3062 state 100% active. Compare the products as supplied first and do not convert 3071 to an active basis without current supplier data. Existing surfactants, dispersants, rheology modifiers and defoamers can interact, so document every component and avoid stacking candidates before their individual effects are known.<\/p>\n

Prepare uniform films<\/h2>\n

ASTM D823<\/a> describes practices for preparing coatings of uniform thickness on panels. Fix substrate, applicator or spray conditions, wet and dry film build, temperature, humidity and airflow. Repeat production-relevant spray or roll application after drawdown screening.<\/p>\n

Check adhesion and impact<\/h2>\n

ASTM D3359<\/a> provides tape-test methods for adhesion. Document failure location and method limits. ASTM D2794<\/a> covers resistance to rapid deformation by impact. Use the required substrate, indenter and film condition and inspect cracking or delamination after a fixed recovery time.<\/p>\n

Validate corrosion as a coating-system property<\/h2>\n

ASTM B117<\/a> describes salt-spray apparatus and operation; it does not set a universal exposure time or predict field life alone. Define scribe, duration, evaluation and acceptance criteria. Compare blistering, rust, undercutting and adhesion retention for the complete coating system.<\/p>\n

Decision rules<\/h2>\n